Categories
over NT$4688 get 5% off on order
Not enough stock.
Your item was not added to your cart.
Not enough stock.
Please adjust your quantity.
Limit {{ product.max_order_quantity }} per order.
Only {{ quantityOfStock }} item(s) left.
Unique features
Reinforced with 20% ultra-lightweight and relatively long carbon fibre stringers
Extremely stiff
Two times as stiff as HDglass (or even more compared to other PETG-based filaments)
Great impact resistance
10% more impact resistant than HDglass (or even more compared to other PETG-based filaments)
Very easy to print
Nearly warp-free, improved thermal stability, nearly perfect first layer and inter-layer adhesion
Good first layer adhesion to a heated glass print bed and many other surfaces
Heat deflection temperature of ± 85° C
Great dimensional stability
General printing guidelines *
Nozzle size: ≥ 0.5mm | Layer height: ≥ 0.3mm | Flow rate: ± 100% |
Print temp: ± 230 - 265° C | Print speed: High | Retraction: Yes ± 6mm |
Heat bed: ± 0 - 60° C | Fan speed: 50-100% | Experience level: Beginner |
*) Above displayed settings are meant as guidance to find your optimal print settings. These ranges in settings should work for most printers, but please do feel free to experiment outside these ranges if you think it is suitable for your printer. There are a lot of different type of printers, hot-ends and printer offsets that it is extremely difficult to give an overall one-size-fits-all setting.
Abrasiveness
Please be aware that CarbonFil filaments contain a relatively high concentration of extremely hard carbon fibres, which have an abrasive nature. In general these carbon fibres will accelerate the nozzle-wear of brass nozzles, much faster than unfilled filaments. We recommend to use nozzles from stainless steel or other hardened alloys.
Filament length
ρ: 119 g/cc | 50 gr coil | 0.5 Kg spool | 2.3 Kg spool | ||
Ø 1.75mm | ± 17.5m | ± 175m | ± 804m | ||
Ø 2.85mm | ± 6.6m | ± 66m | ± 303m |
Nozzle cleaning
When printing with filled/composite filaments it is recommended to clean your nozzle immediately after printing by feeding 15-20cm PLA filament through your nozzle. This will make sure that any potential fillers are flown out of your nozzle. It is even better to use glow in the dark PLA as the extremely hard phosphorous particles are much more likely to scrape out residual waste from your nozzle.
Compliance *
This filament is compliant to below listed directives and regulations.
RoHS directive 2011/65/EC
REACH directive 1907/2006/EC
*) This declaration of conformity to directives and regulations is prepared according to our present standard of knowledge and may be amended if new cognitions are available and applies only for the above described products.
美道家國際Le 3B成立於2007年,早期專注進口歐美各國飾品及生活用品於PChome商店街販售,近年來因3D列印蓬勃發展且公司本身亦投入相關教學工作,有鑑於國內3D列印線材僅能找到國內或對岸廠商的產品,而且種類有限且品質不一,特於2017年初成立『my3DP』3D列印網站,除讓國內3D列印的創客們或教育單位能快速掌握全球3D列印的最新動態,並且能輕鬆購得歐美各國不同類型的高品質、特殊的3D印表機線材及相關周邊,以因應各種不同的需求。
~my3DP, my 3D world~
~我3D印表機,我的3D世界~
訂購與運送說明
連絡電話:N/A
電子郵件:Service@le3b.com.tw
服務中心:桃園市桃園區中正路(內部整理中,僅接受預約)
退換貨政策
隱私條款 | 條款及細則 | 2018 © my3DP