Categories
over NT$4688 get 5% off on order
Not enough stock.
Your item was not added to your cart.
Not enough stock.
Please adjust your quantity.
Limit {{ product.max_order_quantity }} per order.
Only {{ quantityOfStock }} item(s) left.
This is a full outer carton box containing 15 spools of 2.85mm Volcano PLA - White 750gr. We're clearing our warehouse with a huge sale in order to make place for a lot of new products in 2019.
Unique features
High heat resistance of ≥ 95° C after annealing
Less than 0.3% shrinkage after annealing
Roughly 8 times less shrinkage compared to competitor materials available on the market
Engineered to have excellent dimensional accuracy before and after annealing
Engineered for high printing speeds of > 120mm/s
Highly crystalline immediately after extruding resulting in increased stiffness and temperature resistance
Superb mechanical properties comparable to ABS
Excellent interlayer adhesion
Biodegradable
Matte surface finish
General printing guidelines *
Nozzle size: ≥ 0.15mm | Layer height: ≥ 0.1mm | Flow rate: ± 95 - 110% |
Print temp: ± 220 - 255° C * | Print speed: High | Retraction: Yes ± 5mm |
Heat bed: ± 0 - 60° C * | Fan speed: 50-100% | Experience level: Beginner |
*) Above displayed settings are meant as guidance to find your optimal print settings. These ranges in settings should work for most printers, but please do feel free to experiment outside these ranges if you think it is suitable for your printer. There are a lot of different type of printers, hot-ends and printer offsets that it is extremely difficult to give an overall one-size-fits-all setting.
*) Flow rate depends on printing speed and type of hotend used. For full metal hotends a lower flow rate is recommended and for high printing speeds a high(er) flow rate is recommended.
Annealing Volcano PLA
Annealing is a secondary process in which a plastic part is heated up to half of the melt temperature for a moderate period of time before letting the plastic part cool back down to room temperature. When the plastic part is reheated (annealed) like this, the material relaxes and internal stresses and/or strains are relieved resulting in improved dimensional stability, reduction/removal of dimensional distortion and defects, and improved physical and thermal properties of the printed (and annealed) plastic object.
Step 1
Preheat a convection oven at 110° C (half the melting temperature of Volcano PLA). It is highly recommended to use a thermometer to calibrate the exact temperature of your convection oven.
Preheating the oven to 110° C is extremely important as your Volcano PLA printed object will then crystalize in such a rapid timeframe that there is almost no time for the material to shrink. This results in a negligible shrinkage percentage of < 0.3% and by that Volcano PLA is unsurpassed when it comes to reduction of shrinkage after annealing.
Step 2
When the oven is preheated to a stable temperature of 110° C then quickly put your Volcano PLA printed object in the oven. Make sure to do this as quick as possible in order to keep the loss of heat reduced to a minimum. Don’t remove any supports (if used) from the printed object when putting it in the oven.
It is recommended to place the Volcano PLA printed object on a flat aluminium sheet/foil or similar flat metal object to obtain a stable/equal heat transmission.
Small objects – 20 minutes timer
For small objects with thin walls and medium infill annealing will take ± 20 minutes
Large objects – 60 minutes timer
For large objects with thick walls and medium/high infill annealing take ± 60 minutes
Step 3
When the object is annealed taking above mentioned duration into account then switch off the oven and let it cool down to room temperature. Do not remove the object before the oven has completely cooled down to room temperature!
Step 4
When the oven is cooled down completely you remove the object from the oven and remove any support material (if used). Your Volcano PLA printed object is now annealed and has all thermal and mechanical properties as displayed in the Technical Data Sheet (TDS).
美道家國際Le 3B成立於2007年,早期專注進口歐美各國飾品及生活用品於PChome商店街販售,近年來因3D列印蓬勃發展且公司本身亦投入相關教學工作,有鑑於國內3D列印線材僅能找到國內或對岸廠商的產品,而且種類有限且品質不一,特於2017年初成立『my3DP』3D列印網站,除讓國內3D列印的創客們或教育單位能快速掌握全球3D列印的最新動態,並且能輕鬆購得歐美各國不同類型的高品質、特殊的3D印表機線材及相關周邊,以因應各種不同的需求。
~my3DP, my 3D world~
~我3D印表機,我的3D世界~
訂購與運送說明
連絡電話:N/A
電子郵件:Service@le3b.com.tw
服務中心:桃園市桃園區中正路(內部整理中,僅接受預約)
退換貨政策
隱私條款 | 條款及細則 | 2018 © my3DP